Home > Power Supply > Problems After Replacing Power Supply

Problems After Replacing Power Supply

Contents

If these options don't work you could transfer this particular question to the "storage" section. Replacing a power supply is a surprisingly easy process. Is there anyway to test if it's a motherboard or hard drive issue? Have you tried both warm and cold boots? (warm reboot = "ctr-alt-del"; cold reboot means power off then power on again). useful reference

As much as I hate to say it, that is more likely the case. before you go and try to get it tested, get a PS/2 keyboard and see if it works... Do you have another computer around that works? If these options don't work you could transfer this particular question to the "storage" section. http://www.tomshardware.com/answers/id-1842654/booting-installing-power-supply-pictures.html

Installed New Power Supply Now Computer Won't Boot

Try removing the modules and starting the unit with only 1 module in the A slot. Removing resets the BIOS to its default config. If it starts with both modules, you have a bad slot B. Do not add or remove any components.

So im thinking at this point somehting on the motherboard fried when the old PSU went. this is the first time i install a new psu and graphic card so i'm not sure if the wiring is good so i'm going to include pictures.this is my system I thought maybe it was something with my wireless keyboard but I tried a wired one and nothing happened still. Motherboard Has Power But Wont Turn On If it does not start, bad module.

It will be connected to almost every component inside the computer case and will look something like this: 4 Remove the case cover. Replaced Psu Still No Power Sometimes Best Buy has good deals but for the most part they charge 50% more than what you get something for from Newegg, MicroCenter, CompUSA or Amazon. wikiHow Contributor The computer motherboard is the large flat piece, usually in the middle of your computer. http://www.tomshardware.com/answers/id-1682724/power-supply-installed-computer-boot.html and try using different usb ports for your keyboard...

by Brechan / February 5, 2010 9:31 PM PST In reply to: Changed power supply but pc still does not power up I have to agree with geoffwaddell on his checklist; Smps Working But No Power To The Motherboard So the link of the Sempron I gave you can be unlocked to a Athlon X2 (50/50). Desktops are 3.5" and Laptops are 2.5". how is it the board when it posts??

  • More wattage on the package doesn't mean better.
  • These connectors work with either 20 or 24 pin motherboard connectors and will accommodate more types of computers.
  • Click the power button on the case.What do you see?
  • Preview post Submit post Cancel post You are reporting the following post: Changed power supply but pc still does not power up This post has been flagged and will be reviewed
  • That should leave two pins to the left of the switch and an empty slot to the right of the switch.From there:1.

Replaced Psu Still No Power

Does the CPU fan spin?You probably already have done all that, but I just want to verify it. https://www.cnet.com/forums/discussions/changed-power-supply-but-pc-still-does-not-power-up-381672/ What's the best way to get grounded, I know I read to touch the non painted metal part, I don't have one of those static bracelet things, if I go outside Installed New Power Supply Now Computer Won't Boot CPU: AMD A8-3870K APU 4x 3000 MHzGPU: MSI Radeon HD 7850 1gb OC EditionRAM: 4GB DDR3-RAM Micron/ElixirMotherboard: Listed above, but it's a ASUS F1A55-M LK R2.0Sound: OnBoard 7.1And the case: ATX Power Supply Works Computer Wont Turn On Then remove the motherboard battery.

You don't have to go with this one in particular, this is just an example. http://wphomeguide.com/power-supply/notebook-power-supply-problems.php I can see some but not all of my files and when I try to copy them it says I don't have permission and in one case when I tried to A few hours... I've transferred a couple more files by changing the security on each file because the folders don't allow it. New Psu No Power

really. the comp is turning on and giving you the option to enter the bios. Tie me down: The ultimate guide to... http://wphomeguide.com/power-supply/power-supply-problems.php Not bad huh?

TechSpot is a registered trademark. Pc Not Turning On Motherboard Has Power It shows on your boards spec sheet it has two SATA ports(but doesn't mention the interface of the HDD) If it is SATA you could just plug it into another comp. solved I installed a new power supply but the computer won't boot solved installed new vga, power supply, and ram computer wont boot New video card and Power Supply, but now

Is it just a little higher quality product or something?

Or was I just lucky?Rickylee psu's from brands like Antec, corsair etc ( quality ones ) usually have overvoltage, overload protection so when psu detects sudden current spikes it will shut hopefully that's it because if the usb ports are dead you'll essentially have to replace the board. Attach the CPU Cooler.5. Psu Paperclip Test So im thinking at this point somehting on the motherboard fried when the old PSU went.

Good thing you said don't stick your hand in there cause I was just upstairs on carpet. Also with my computer being so old is it still easy to transfer the files, I know there is some difference with the ribbon cables I have in mine and what's The most obvious clue is that the system will do absolutely nothing when you hit the power button. Get More Info Also does anyone know how to fix my problem with being stuck on the Compaq page?

The RAM appears to be fine. Your HDD is connected with ribbon? CUDGEdaveMember Since: December 24, 2010Posts: 2590CUDGEdaveFollowForum Posts: 2590Followed by: 0Reviews: 7 Stacks: 0Forum Karma: 0#3 Posted by CUDGEdave (2590 posts) - 5 years, 1 month agoWhen the PSU blew it MAY cmac813Jul 23, 2011, 3:31 AM RussK1 said: Encrypted huh?

cmac813Jul 16, 2011, 9:19 AM RussK1 said: before you go and try to get it tested, get a PS/2 keyboard and see if it works... Is it easy to do? Shorting one by mistake feels just like being electrocuted by 120 volts from a receptacle. How to install an Intel or AMD CPU in...

If you neglect this step, you may damage your computer. 2 Disconnect all external connectors (including the power cord) from the machine. wikiHow Contributor Buy a new cord to replace the damaged cord. It's taking a while and I'm sure there is a better way but I can't figure it out so I'm at least able to get some. in the end im probably going to just build an entire new system.

So I can basically buy any that are IDE to USB enclosure 3.5" and then I can hook my hard drive up to the enclosure and connect it to my laptop Unplug all components from one another. If you are sure the PSU is okay, then I would believe that there's problem with something else ...

© Copyright 2017 wphomeguide.com. All rights reserved.