Home > Power Supply > Power Supply Question

Power Supply Question


If I were you, I'd make an oscilloscope. This type of circuit is generally known as a voltage multiplier. This product also includes the ability to perform AC leakage testing and has a convenient adjustable power supply for soldering irons. Another time-saving technique is to re-use the same components in a variety of different circuit configurations. get redirected here

Germanium Silicon Carbon None of the above Answer : 2 Q16. A tale of two sources: Is TLS *defense* against Man-in-the-Middle, or not? What's the best way to test a power supply under load? Notes: Ask your students what the term “loading” means in this context. http://www.completepowerelectronics.com/power-supply-related-interview-questions-answers/

Power Supply Test Questions

Q. Q. Notes: Challenge your students with this question: is this the right kind of filter circuit (low pass, high pass, band pass, band stop) to be using, anyway? Yes, dividends are paid on a quarterly basis, dependent on the performance of the business in the relevant period.

Inductor L1 fails open: no voltage across load, no current through load, no current through rest of secondary-side components, little current through primary winding. Learning to mathematically analyze circuits requires much study and practice. Instead, students need to develop diagnostic procedures not requiring removal of components from the circuit. Interview Questions On Uninterrupted Power Supply If the wire is insulated, special insulation piercing probes are available, such as CalTest Electronics CT3044, or the Pomona 5913.

They are having low reverse recovery time (Trr). Multiple Choice Questions On Uninterrupted Power Supply What is true about the breakdown voltage in a Zener diode? It is sometimes referred to as startup current and it's generally several magnitudes greater than the steady-state value of the supply.InverterA electrical device used to convert DC to AC power.Remote sensingProvided click for more info Voltmod, Sep 27, 2016 #1 Voltmod New Member Messages: 3 Well here's an update - I purchased a second power adapter from NI to keep isolating the issue.

Question 9 What does it mean if a power supply has a DC output with 5% ripple? Ups Interview Question The circuit elements you identify as either possibly faulted or properly functioning can be wires, traces, and connections as well as components. Better to solder just a cable Enrico Gefällt mir 0 gefällt das anzeigen(0) Antworten Aktionen Re: Power Supply Question Andy Clark (Workshopshed) 23.12.2016 10:55 (als Antwort auf: balearicdynamics) The kit versions Describe the limitations of the circuit shown, and explain how some of the other filters would do a better job.

Multiple Choice Questions On Uninterrupted Power Supply

Mathematically analyze the circuit, solving for all voltage and current values. http://electronics.stackexchange.com/questions/224248/questions-about-a-basic-power-supply The metal covers of instruments and appliances are connected to ground (and hence called a safety ground). Power Supply Test Questions Burnt electronic components usually produce a strong and easily-recognized odor, always indicative of overheating. Uninterruptible Power Supply Questions And Answers Exploit the convenience inherent to your science, and get those students of yours practicing their math on lots of real circuits!

voltage to regulated or ordinary power supply increases by 5% what will be the approximate change in d.c. Get More Info One way you can save time and reduce the possibility of error is to begin with a very simple circuit and incrementally add components to increase its complexity after each analysis, If your scope can't do the multiplication, you can still measure the RMS values of voltage and current, measure the power factor, and multiply the three together. Notes: In a filtered DC power supply, the only time current is drawn from the rectifier is when the filter capacitor charges. Ups Technical Interview Questions And Answers

  1. Alle Rechte vorbehalten.
  2. I'm guessing that this reduces the total allowed power output from the 500W it is rated at to below 100W or so, but it is currently powering two raspberry PIs and
  3. Discuss these issues with your students in the same Socratic manner you would normally discuss the worksheet questions, rather than simply telling them what they should and should not do.
  4. This can be quite significant because of the duty cycle of the current that charges the capacitor: - The charging current that restores the capacitor's peak voltage occurs over a much
  5. Browse other questions tagged power-supply voltage rectifier rms bridge-rectifier or ask your own question.
  6. A.
  7. steveastrouk -max-3 years agoReplyNo, HIGHER switching speeds, done right, are much more efficient, components are smaller, emissions lower.
  8. Power Supply Application http://www.amtex.com.au/ApplicationNotesPower.htm Using a power supply to generate a DC offset with a function generator If a signal source such as a function generator does not have a DC
  9. In a Zener voltage regulator, the changes in load current produce changes in …………….
  10. If your goal is to educate theoretical physicists, then stick with abstract analysis, by all means!

Question 30 A technician is troubleshooting a power supply circuit with no DC output voltage. Thus, if it is operating a circuit and the AC power fails, the power supply will again start supplying power when the AC power comes back on. In summary: Knowledge, Speed and Flexibility set XP apart from its competitors. http://wphomeguide.com/power-supply/power-supply-fan-question.php The connection method is shown in the following diagram.

The seller is Native Instruments, and it came in official NI packaging. Mcq On Ups A mobile cart containing a computer, printer, and scanner gets +12, -12, +5, and +3.3 V directly from the UPS for the computer, printer, and scanner, and the monitor gets 120VAC Avalanche mechanism Zener mechanism Both Zener and avalanche mechanism None of the above Answer : 1 Q12.

Output = DC Output = AC Input = AC "Wall wart" Bench power supplies Battery charger Isolation transformer Variable AC supply Frequency changer Input = DC DC-DC converter Inverter Generator

What is the load regulation? 09% 87 % 72 % None of the above Answer : 1 Q25. I have read somewhere that the. And, if you really want to know more about me, please visit my "About" Page. Ups Questions And Answers Reveal answer Hide answer VTP1−TP2 = 120 volts AC VTP1−TP3 = 120 volts AC VTP2−TP3 = 0 volts VTP4−TP5 = 12.63 volts AC VTP5−TP6 = 12.63 volts AC VTP7−TP8 =

Peak inductor currents exceed the mean inductor current by some margin. The best supplies can be 90% efficient or better. Power is delivered to the utilization site using a pole mounted or other type of transformer. this page The fact that the diode experiences a reverse voltage twice that of the peak AC voltage is something we may exploit!

This is also known as the crossover point.Overload protectionA protection feature in most DC power supplies to prevent any device from drawing more power than the supplies are intended to produce.Overvoltage A. I don't want to use any prebuilt chips where you have a magic black box with inductors, capacitors and resistors connected to it. Notes: Troubleshooting scenarios are always good for stimulating class discussion.

© Copyright 2017 wphomeguide.com. All rights reserved.