Home > Power Supply > Power Adapter Modifications

Power Adapter Modifications


The worst seems to be where an attempt is made to operate portable devices off of an automotive electrical system. More »More by andrea biffi:Add instructable to: Contest GroupRelatedDisassembling and Cleaning Xbox-360 Power Supply ( Brick )by jacob5680use a xbox 360 power supply to power a amplifierby Blake SurovikHow to turn SAFETY For the common transformer based AC adapter, there is no danger anywhere inside the device once unplugged. Back to AC Adapters and Power Supplies Table of Contents. my review here

Please if you're not familiar with electronics, inform about danger of electricity on some trustworthy sources (a simple but comprehensive one could be www.dummies.com) Step 1: the original brickShow All Items i don't get that. I located the resistors that are responsible to set the output voltage. There are several models of cigarette lighter cords, however the actual 12VDC car plug in _interchangeable_ and connected to the cable using a 4-pin modular telephone handset jack. http://hackaday.io/project/3469-modifying-a-notebook-power-supply

Change Output Voltage Power Supply

Failures of one or more of the outputs of these hybrid regulators are very common. I used the kind found in mains power centrals in residential housing, the copper is so thick it actually takes some effort to bend it. Idea to this mod was found here: www.qrp4u.de If you want to know more about switchmode converters get the "bible" called: Switchmode power supply handbook by Keith Billings. Once they are loaded down, the voltage will drop.excellent!

  • Now, the power supply schematic looks a bit like this.
  • Needless to say, if you experience any strange or unexpected behavior with a new adapter, if any part gets unusually warm, or if there is any unusual odor, unplug it immediately
  • I think that you are talking about an unregulated power supply containing a transformer because the voltage in your example drops about 2-3V.
  • New, insulated jacks and all works fine.
  • I wonder how many people have ignored the warnings when their equipment stopped working and replaced that fat "plug"?
  • This is also needed if your load (or radio) has big capasitors in parallel with the power supply line.
  • Common problems - dried up capacitors, shorted semiconductors, and bad solder joints.
  • Use one with an automatic disconnect (3 terminals) if possible.
  • Some rights reserved.

Is it toast? So I picked up the wall wart and started to play. Just drill a couple of holes in the aluminium and we're good to go. How To Change Output Voltage Of Smps However, setting the output to 15 V, the supply shows 14.995 V, and the multimeter shows the same.

The connectors should be identical (including the size of the center hole). This even applies to equipment from the same manufacturer! I had the use of a 150W electronic load, but a 60W light bulb would be more than adequate. http://www.instructables.com/id/the-Brick-PSU/ Fresh batteries can provide quite a bit of current without their voltage drooping that much.

If you need a bigger power supply just buy one, that would be much easier and cheaper.yes, explained like you just did, makes more sense to go shopping for the right How To Change Voltage In A Circuit For shock and fire safety, any wall adapter you use should be isolated and have UL approval. Select the filter capacitor to be at least 10,000 uF per 1000 mA of output current with a voltage rating of at least 2 x Vin. This would be the easiest to repair.

Change Output Voltage Laptop Power Supply

In the first case, it could be a blown fuse, bad startup resistor, shorted/open semiconductors, bad controller, or other components. If this is the case, disassembly is possible without damage, at least in principle. Change Output Voltage Power Supply Some kind of load is required for the power supply output. Laptop Power Supply Hack everything is possible but not everything make sense.

This will effectivley double the output voltage Remove all of the other secondary rectification components Disable the Over Voltage Protection (OVP) circuitry to prevent it from shutting the power supply down this page Adding an IC Regulator to a Wall Adapter or Battery For many applications, it is desirable to have a well regulated source of DC power. There was enough fluff from the caps to have the chassis rated at least R-10 :->). Remove Contributor Are you sure you want to remove yourself as a contributor for this project? How To Increase Dc Voltage Output

Usually, the point of the break is just at the end of the rubber cable guard. The 5V is always handy for use as a USB phone-charger.More CommentsAbout This Instructable 211,436views685favoritesLicense:andrea biffiwww.andreabiffi.itFollow2466Bio: I'm an Italian freelance structural engineer, graphic designer and photographer. If the fuse blew and the readings are too low, the transformer primary may be partially or totally shorted. get redirected here Also see the section: Comments on Importance of Thermal Fuses and Protectors.

containing just a few parts. How To Adjust Voltage Regulator Sometimes these actually will save the day. The voltage you measure (AC or DC) will probably be 10-25% higher than the label specification.

If this one blows immediately, there is a fault in the power supply or one of its loads.

If it is a normal adapter, then the only danger when open are direct connections to the AC plug. A supply designed to deliver 12 amps can be a small-scale spot welder before its overcurrent protection kicks in.Current is the dangerous property, and perhaps 12A are not deadly, but they're The outcome was a variable power supply that could supply between 3V and 48.5V at power levels up to 150W - ideal for what I wanted. Atx Power Supply Voltage Adjustment Overheating or failure may result immediately or down the road with a wall adapter which supplies more voltage than its nameplate rating (as most do especially when lightly loaded).

Devices with more constant power requirements may operate happily at these reduced voltages. Using AC Adapters in Series for Higher or Lower Voltage Wall adapters are totally isolated from everything (except possibly for a very high value resistor to one side of the AC Depending on the type of equipment, there may be a single output of several outputs from the power supply. http://wphomeguide.com/power-supply/power-supply-and-power-jumper.php If the case is regulating the output you can use a switching step-down DC-DC converter for about $3 on eBay.


IC5, how do i learn if it is a regulated out?

Pulsed loading (as in an interrupted SSTC) is unsuitable for this type of power supply as the high current looks like a short circuit and the supply shuts down. Batteries are found in all sorts of portable equipment nowadays. AC adapters (may also be called: wall adapters, power packs, or wall warts) are those boxes hanging on the end of the power cords of many modern consumer electronic devices. That is round about 10kOhm.

ATX Modification An ATX power supply can be modified in much the same way as the main converter architeture is very similar to that of the AT.

© Copyright 2017 wphomeguide.com. All rights reserved.