I don't know if this is relevant but I figured I'd mention it for the sake of completeness. (System Specs up in the corner) Mar 25, 2009 #1 red1776 Omnipotent Still nothing. If you believe this post is offensive or violates the CNET Forums' Usage policies, you can report it below (this will not automatically remove the post). Tried that, same result. check my blog
What kind of problem would the mounting stud cause? I tried unplugging the power to the computer, resetting the bios, removing the bios battery for 5 minutes, reseading the RAM and the video card. I just so happen to have a disk image of my working operating system. If you don't know where that is, open up the motherboard manual book and find the diagram of the motherboard.
Some one puts a stud in where it doesn't belong. Plug the PSU into an AC outlet.3. Cannot boot PC after installing new power supply and graphics card. no monitor signal, no post, no beep solved New case, computer powers on but no display or POST beeps.
After a couple of seconds I hear a series of ticks (sounds like they MIGHT be coming from the processor) and the CPU fan revs down for a second as though Any ideas? Pc won't boot up to anything with new graphics card and power supply Installed new power supply now computer wont turn off by itself Computer won't display after installing new power New Power Supply Turns On Then Off WesloGliAug 4, 2015, 7:36 AM I have a Dp67bg Intel Motherboard and an intel i7 2600k.
First, shutdown your computer. Replaced Psu Still No Power This should tell me if the board is dead or not. Other benefits of registering an account are subscribing to topics and forums, creating a blog, and having no ads shown anywhere on the site. http://www.tomshardware.com/answers/id-2633416/power-supply-installed-computer-boot.html What i did next, is to remove my old psu and put back the new thermaltake psu with the exact same wiring, kept the old graphic card inside the pc for
Rinse and repeat. http://www.tomshardware.com/answers/id-1842654/booting-installing-power-supply-pictures.html No POST, no BIOS, no logo screen, nothing. Changed Power Supply Computer Won't Boot Media Center: Motherboard: Gigabyte mp61p-S3, Processor: AMD Athlon 64 x2 6000+, Memory: 6 gigs Patriot DDR2 800, Video: Gigabyte GeForce GT730, Storage: 500 gig Hitachi, PSU: Seasonic M1211 620W full modular, Power Supply Works Computer Wont Turn On No POST, boot loops, or restricted to a 2gb stick.
Attach the 4-pin CPU power connector.3. Thanks in advance! I plugged in the 20+4 pin main power, the 4+4 pin CPU power, 2 SATA power plugs for my optical drives, 1 SATA power plug and 1 molex plug for my Check what voltages that are supplied to the processor - honestly, gotta be some common ASUS issue.Click to expand... New Psu No Power
PSU should be enough but that does not mean you could not be overloading one of your rails. Sorry, it's my first time booting up a new mother board so I have no idea what it's suppose to do. Anyway, it's located in the bottom right corner, just to the left of the big blue SATA port. I had my pc running overnight and when I woke up my router wasn't powering up and neither was my pc.
Maybe try for a BIOS upgrade, it could be a BIOS issue, although that seems unlikely as it was working previously.... Psu Paperclip Test Place the CPU on the motherboard. i hope not,Click to expand...
by Fredxxxxx / February 5, 2010 2:31 PM PST In reply to: Just tested Power Supply Can you see an LED on the motherboard when you turn on the power? Preview post Submit post Cancel post You are reporting the following post: no signal on monitor after changing power supply This post has been flagged and will be reviewed by our Ask a question and give support. How To Install Power Supply Silence, long single beeps, or series of short beeps indicate a problem with the memory.
Site Changelog Community Forum Software by IP.Board Sign In Use Facebook Use Twitter Need an account? by R. The new one was pretty much right on except for +3.3v which showed 3.2 as well, 12.2 for the -12v and 270ms for PG.When I installed the new power supply the At this point, the system should POST successfully (a single short beep).
Aizat AshaariMar 8, 2014, 4:27 AM I have the same problem... We spent a lot of time on this.
© Copyright 2017 wphomeguide.com. All rights reserved.