Home > No Signal > No Beep. No Signal. Nothing. HELP

No Beep. No Signal. Nothing. HELP

Contents

Those may have been bad cases but are examples that BIOS/hardware issues can make it take long before posting and working normally, so if you haven't done already, wait a reasonable If not, its most likely the CPU. any other ideas? I wait 5 or so minutes to see if my computer is going through its start up process and is reaching Windows which usually triggers my mouse and keyboard to light check my blog

But THX everyone for their help and suggestions. When I touched the CPU cooler it was really really hot..... And dead. Reply Report Krizom- Oct 8, 2012 at 01:43 AM thank you so much now I can go on my computer! :D Reply Report nix- Oct 8, 2012 at 05:59 AM Thanks http://www.tomshardware.com/forum/id-2707576/computer-beep-boot-signal.html

Computer Monitor No Signal

JawstinDec 28, 2014, 12:06 AM alexoiu said: What are the 4 digits after SN in the board's serial (SN14xx)? I did rule out the video card by switching it out with my old one that is compatible. All the other components appear to be running fine, all fans spin, and the HDD appears to be running, there's just no display going to the monitor.

I tried the Pressing power button without the power cord trick but it didnt work then I remembered that only the KB and mouse have to be plugged in so I still no beeps, and nothing displaying on my monitor... My PC is still really new only about 2 months old and its a pretty decent rig. Computer Turns On But No Signal To Monitor Well, I'm not very god when it comes to hardware.

Ask a question and give support. No Signal On Monitor When Cpu Is On TechSpot is a registered trademark. PC runs great. my review here I had the same prob wid my intel p4 3.7ghz 1gig ram.

Following advice on the website geekstogo it was suggested for CMOS removal. Pc Monitor No Signal Detected I also get a high cpu temp warning.The bios hardware monitor tells me that my CPU is at 97 degrees celsius ( around 200F ), and this is just at idle From there I switched the RAM sticks around so what was my #1 RAM was then placed in the socket where its sibling lived and vice versa. But I get no visual, no beeps.

No Signal On Monitor When Cpu Is On

My Specs :RAM : 1GB DDR2No GPU , using Intel G33/G31 Express ChipsetMotherboard : Asus PK5ML-AM IN450W Power Supply 500GB , 150 GB , 40 GB HDD'sNo Optical drive , using https://steamcommunity.com/discussions/forum/11/350544272215819110/ Still, it might be better to have a technician do it, as touching all the components in your case could make things worse (Trust me, there's worse). Computer Monitor No Signal Might take a while for them to drop but hey, 1 and a 1/2 month now without a pc and I'm starting to discover the outside world, them trees n clouds, My Monitor Says No Signal When My Computer Is On It did not reach this point and the only way I can power off the machine is by holding down the power button for 5 seconds.

Thanks ! click site Melde dich bei YouTube an, damit dein Feedback gezählt wird. But it did work! After having 2 RAM's inserted to the yellow slots, first 2 sets have done nothing, replacing the first RAM in the first yellow slot, led to the beeps, and lighting on Monitor Shows No Signal But Cpu Is Running

How to Reset Your BIOShttp://www.wikihow.com/Reset-Your-BIOS JawstinDec 28, 2014, 9:28 AM Chicano said: Jawstin said: And here is all the other test I've done :NOTE that all these test were done without Get the answer alexoiuJul 21, 2016, 3:09 PM Are you connecting the monitor to the graphics card (not motherboard)?If yes, and still no signal, try removing the card, connecting the monitor It was a frontal collision, a mild one... news Thx Report edwin- Mar 13, 2009 at 06:00 AM Hi,ihad that prablem my screen show blue and says Error and says you have toclean some memory but I toke my coputer

Amr_3 6 posts since Dec 2016 Newbie Member Can't Access Nighthawk Router Login Page Last Post 3 Weeks Ago Hello Daniweb Community, I've been given a Nighthawk (R7000) to checkout to No Signal On Monitor Acer A friend of mine had the same issue on a new FM2+ build Asus mobo with the same chipset and a A-6600K APU... All rights reserved.

You might have to check your manual to see if one of the slots has to have a stick in it.

So I am thinking it is Motherboard or Processor since even in its bare bone form it gives the same issue. Mar 3, 2012 #5 Buckshot420 TS Enthusiast Posts: 301 UNPLUG YOUR PSU FIRST!!! 1) Make sure you have both 24 pin and 6 pin power cables connected to your board. 2) But even so it must be allowing the CPU to work partially or else the display would be completely blank... Monitor No Signal Hdmi I tested a bare bone power up (Motherboard, Processor, 1 Memory Module, Power Supply, and Video Card), and still encountered the same issue.

Any and all assistance would be greatly appreciated. 0 rmrd 9 Years Ago Unplug the four-pin connector from the board completely, and then try to turn on the computer again. So my compy just won't start. You might have bumped it off, considering how hard you bumped it). http://wphomeguide.com/no-signal/no-signal.php Now, I'm met with 1 long 3 short, and after a while 1 short beeps..

last nite I had kicked the CPU accidentally and the mouse came loose. No beeps like it usually does. Lol. Over time many people have experienced that this P4 connector deteriorates and becomes loose and unreliable.

Upon inspection of cords and their input connectors, I noticed the 12v connector seems like it might have been burnt on 2 of it's 4 sockets. 2 of them look browned Just checking if the BIOS does support the CPU. I have a compaq presario c700 notebook which is quite old..... The first thing to rule out is overheating (CPU, motherboard, hard drive or power supply) then I would check for bad memory (if you have two modules - swap them out

so luckily checked this forum on my iPhone. solved Built a new computer, I get the post beep but no display signal. Check your motherboard light if it is on then restart computer and check display of board by press del or f2 key if display come then unplug the hard disk wire Keep us updated!

Monitor is Working properly by Connecting It To My Laptop . Edit by mod; expletives deleted (VM) Reports: · Posted 5 years ago Top GuiltySpark Posts: 4024 This post has been reported. Report keen- Aug 28, 2009 at 07:30 AM theirs no signal on my minitor 1 2 3 Next Ask a question Member requests are more likely to be responded to. ThanksXINY Helpful +61 Report xpcman 16837Posts Wednesday October 8, 2008Registration date ContributorStatus January 18, 2017 Last seen Nov 5, 2008 at 10:07 PM It does sound like a major problem.

ChicanoApr 4, 2015, 7:33 AM alexoiu said: " He says a BIOS message tells it doesn't recognize the CPU" That post is from 2008 and is not related to the issue I guess if the problem persists I'll try that.

© Copyright 2017 wphomeguide.com. All rights reserved.