Home > Hard Drive > Problem With Slave Hdd

Problem With Slave Hdd


More resources See also my computer was fine then one day it said keyboard falure error auto sensing secondary master hard disk drive and it says to p solved Computer doesn't That is because it could be the cable itself, the connector on it, or some components inside the PSU that power up that particular cable/line. If you get the error message, there is a chance your drive is dead or dying. The cable key is a small plastic square on top of the connector on the ribbon cable that fits into a notch on the connector of the device. useful reference

Or I'm even guessing, Either way, power still gets to both hard drives technically all the time. You can also seek out a company that does data recovery, rather than buying the software yourself.ConclusionBecause so much is stored on hard disks these days, knowing how to revive a Since it's doing the samething for my 10 GB Hard drive that I havent used in a long while. Extended tests have been run twice on the disk with no problems, except the statement "Smart status - not available".

Hard Drive Problems Troubleshooting And Repairing

If you see neither, try visiting the drive manufacturer’s Web site to see if a diagram is available.Checking SCSI terminationIf the machine uses a SCSI drive, there are two factors with This comes in handy when you aren’t sure whether or not the drive is working, because you can get an answer immediately rather than rebooting and waiting to see whether the See the picture below...

  • This position is used to ensure that the cable is attached to the drive in the correct position.
  • On systems where the pins are bare instead of surrounded by a plastic ridge, it’s easy to offset the connector by a row or two on the pins.
  • Tom's Hardware Around the World Tom's Hardware Around the World Denmark Norway Finland Russia France Turkey Germany UK Italy USA Subscribe to Tom's Hardware Search the site Ok About Tom's Hardware
  • Not showing up in "My Computer" except for having to re-activate it.So I think it might be an operating system issue.
  • Fourth master - not detected.
  • You can also find and install a driver called dynamic disk overlay that serves as a medium between a large disk drive and the old BIOS.

It’s possible for plugs to jiggle loose when moving a PC, and it’s easy to uproot a ribbon cable connection when pulling circuit boards or performing other maintenance tasks inside the The settings differ for every drive, but this problem has to do with that setting. When I run a scan disk utility, it finds occasional errors. Hard Disk Troubleshooting Software Replace my second drive F with a new Seagate ultra ATA 300gb, then throw away the old one.

Pull the jumper completely off and reboot Oct 3, 2006 #5 idontknow000 TS Rookie Topic Starter ok i fixed the jumpers they werent on right. External Hard Disk Troubleshooting So it Could be a power supply issue.So I unplugged the Power Cord to the Power Supply. Once done I put my hdd back in as it was but now I'm having problems booting. http://www.techrepublic.com/article/troubleshoot-hard-drive-failures-in-seven-easy-steps/ The fact that the boot disk’s OS cannot read it does not necessarily mean there is a problem with the formatting.

In order to use Cable Select jumpering, several conditions must be met. Troubleshoot Hard Drive Windows 7 These settings are not an issue when troubleshooting a drive that has suddenly gone bad in an existing system, but if you are moving a drive from one system to another It's that way for a reason. I would say make a backup of the important data from that drive at the first sign of trouble.

External Hard Disk Troubleshooting

Guess what happened to me today. https://people.richland.edu/dkirby/hdproblems.htm My computer motherboard is a Soyo K7VM333.... 2 months ago, I replaced my 1.1 ghz AMD Duron with a 2.0ghz AMD Sempron 2800+ (Identified by computer as a 2.0ghz AMD Athlon Hard Drive Problems Troubleshooting And Repairing If you get a specific error message, base your troubleshooting on this information. Hard Disk Troubleshooting Pdf Your letters will change if you have created a primary partition on the new drive.

That it increases the chances 100% that my secondary Drive will show up in My Computer.I don't know what this means. http://wphomeguide.com/hard-drive/master-to-slave-virus-transfer.php If it does, run the program to erase all data on it. My sources tell me that there was a loose standard to put the Master drive on the end of the 40-wire cable and the Slave in the middle but that was It's probably not good for it to mount it upside down, though. Hard Drive Troubleshooting Flowchart

I wouldn't. I think it should be shown as 'Third IDE slave", although whether this will fix the SMART problem remains to be seen, but I can find no way of changing the When I added a new Hard Drive, all my drive letters changed! this page I will just copy and paste my post here (Sorry if this isn't allowed. "Hey everyone, I am having a problem...

If I switch the two, technically, I'm guessing the hard drive wont boot up the operating system? How To Troubleshoot Hard Disk Error I put a different hard drive in. Then it popped up and found the hard drive.

I'm kind of confused on what you want me to test here.And those other two 4 pin connectors to my DVD drives pretty much can't reach my hard drives.

The Hard drive didn't appear in "My Computer", so I went to computer management > Disk management. If not check the power source and ide cable Is the floppy light constantly on? In most cases, yes. Hard Drive Problems Symptoms The blue connector should be installed into the Primary IDE connector.

Dismiss Notice TechSpot Forums Forums Software Windows Today's Posts problem with slavehdd Byidontknow000 Oct 2, 2006 alright i need your help. Thank you for helping us maintain CNET's great community. You can leave the drives in the working configuration and transfer the necessary data from the original drive (now slave) to the new master drive. Get More Info I would have to replug them in.

If I were in your place, and I knew that my PSU is old, I would go ahead and replace the PSU first. This stripe tells you that the wire on that side is attached to Pin 1 of each connector. The secondary hard drive didn't even appear in the BIOS. Also, make sure you shut down Windows properly.

In fact, there is no pin at that position. solved internal secondary hard drive is freezing computer. Oct 5, 2006 #7 smore9648 TS Rookie Posts: 697 idontknow000 said: ok i fixed the jumpers they werent on right. now when the slaves connected bios recognizes it and it gets past the startup and theres a black screen that says "press A key to reboot" Oct 4, 2006 #6

If using the 80-wire cable, attach the blue end connector to the system board or host controller, the gray middle connector to the Slave, and the black end connector to the It’s also not a very friendly program to use, and it has trouble writing the recovered files to anything except a FAT16 drive.At the other end of the spectrum is EasyRecovery Now do the same for the mobo end of that same cable. house70Jul 31, 2011, 10:45 PM If you can reproduce those findings every time, we have it nailed down.

Along one side of the cable is a stripe. I think you are right about the Power Supply , because I didn't think about that, until you mentioned it.It could be the 4 pin connectors are dirty, or it could thanks Oct 2, 2006 #1 blue_dragon TS Rookie Posts: 190 bios go into the bios and make sure the computer is booting off the correct hard dirve Oct 2, Until then, you can run on 1GB of RAM, for WinXP it should be enough.Good luck with this project.

© Copyright 2017 wphomeguide.com. All rights reserved.