Home > Hard Drive > Problem In Installing Seagate ATA HDD As Primary Slave.

Problem In Installing Seagate ATA HDD As Primary Slave.

Contents

Installing a SATA Hard Drive on Windows 2000: Single Install: For proper installation of a drive using Windows 2000, simply allow the operating system to partition and format the drive during Reply Ravi says: August 14, 2007 at 8:38 pm I need to install a Sata 160GB to my 3″ external drive, The manual does not tell much about it so is Step 4: Configure the BIOS Next, boot into your PC's BIOS-setup utility to verify that it recognizes the new drive and positions it correctly in the drive hierarchy. (Check your PC's Cable-Select Option (Default) - Use with Ultra ATA cables. http://wphomeguide.com/hard-drive/problems-instaling-seagate-slave-drive.php

Click Next yet again (to the Format Partition screen), and ensure that "Format this partition with the following settings" is selected and that the "File system" drop-down reads "NTFS." Click Next Click next and soon the new drive is available. How We Test Laptops Still lost? Flag Permalink This was helpful (1) Collapse - I've had this config.

Install New Hard Drive Windows 7

If you plan to replace your boot drive with the new drive and don't have an empty bay, your upgrade will involve more steps than we can cover here. Congratulations, your new drive is installed!  Now that you have installing your hard drive under your belt, you might be interested in partitioning your hard drive (that means dividing your space so Note: If your controller supports RAID, you may need to define your drive in a RAID Array before Windows will see the drive, even if the motherboard or system drivers are

My hard drive doesn't have the jumper settings on the label: Find the model number and visit the manufacturers website. Here are some images of Serial ATA cables.  Click to expand.  The BIOS will not detect a hard disk if the data cable is damaged or the connection is I went into the BIOS setup and this is what it said:Primary IDE Master: (WDC WD400BB 22JHCO)Primary IDE Slave: (STE380012A)Secondary IDE Master: (HL-DT-GCE-8526B)Secondary IDE Slave: (not detected)what does this mean I How To Install Seagate Hard Drive On Pc It also provides our default jumper settings for most WD drives.*END Critical: Some of the instructions in the articles below are Data Destructive and cannot be undone.

Of course I haven't really looked into it. How To Install A Hard Drive In A Laptop i'm building a new machine.have an old wd 16 gig ide & new wd 160 gig sata. With both drives set to Cable Select, the computer will recognize the drive hooked up to the black end connector as the master and the one hooked up to the middle Thanks alot.

Open Computer Management and select Disk Management. What Is Sata Hard Drive Mean Once your drive has been partitioned and format verify it appears under My Computer. Reply Elliot says: August 11, 2007 at 9:03 am Thanks! Return to Top Windows XP The Windows XP Operating System has all the necessary tools to properly install a Serial ATA (SATA) hard drive, EIDE hard drive, or Solid State drive

  • No, you are right.
  • i installed a new seagate sata drive and was able to figure out how to make it boot instead of my 2 WD IDE's but now i am having a problem
  • For specific details, see Answer ID 127: Error message: No mass storage device found is reported during installation of Windows 2000, XP, Vista, or 7.
  • Flag Permalink This was helpful (0) Collapse - It's fine by ackmondual / July 22, 2005 11:48 AM PDT In reply to: Mixing SATA and IDE drives in a system?

How To Install A Hard Drive In A Laptop

I upgraded the IDE with a SATA adapter(should I remove the jumper then?). I installed the second hard drive and notice that some files were missing. Install New Hard Drive Windows 7 If you want a single partition (single drive letter), click on Next and your hard drive will be automatically partitioned and formatted as NTFS and Windows 7 will continue installing. Install Seagate External Hard Drive Then, after paying $70 bucks he restored it (with all files gone) he told me I had a virus and not to download free music anymore and always update my security

Most motherboards have two IDE channel connectors. Get More Info malcolm Reply angie says: November 11, 2007 at 3:44 pm hey i have been trying to get this to work ok so this is what i am doing i have a Reply Mark barbee says: August 31, 2009 at 7:25 pm Here's one for ya. You can use your BIOS to adjust the boot device priority in order to select which drive you want to run your OS from. 0 416azn4lyfe 10 Years Ago As I How To Connect Sata Hard Drive To Motherboard

I want to say Thank YOU!!! Also just out of curiosity, if you upgrade your hard drive beyond 120gb and say I had a 60gb prior I read somewhere that you would need to purchase a driver Make sure that your system BIOS is properly configured. http://wphomeguide.com/hard-drive/problem-with-slave-hdd.php Our SATA drive has a 15-pin SATA power connector.

I have hooked everything up correctly as you described but when I boot up my computer it freezes on computer screen,when I disconnect the wires and restart it boots up normally?I How To Install Seagate Hard Drive On Xbox One I ask because here's the setup I am faced with: Three hard drives, a new motherboard that can control up to six SATA drives, two of the drives are actual SATA About Ziff Davis, LLC.

If the drive still is not detected after testing the cables, contact your controller card manufactuer to see if there is an update available.

Input the capacity of the partition and click on the Apply button. Preview post Submit post Cancel post You are reporting the following post: Mixing SATA and IDE drives in a system? Adding an additional hard drive to a Windows XP installation: Make sure your hard drive is detected by your Serial ATA or EIDE controller. How To Install Seagate Hard Drive On Mac NIce to see some floridians.

I had no idea that "disk management" section existed 😀 Once i found it i initialized the HD and am currently formatting it. Western Digital highly recommends partitioning your drive in this manner. BUT sometimes it is best if the HDD is the port Master and connected to the END plug. this page All three settings blue screen on me.

I have them reconnected this same way. Enable LBA mode and UDMA mode, if applicable. So be sure you have the driver on a floppy and it should have come with your motherboard. Couldn't work out how to be able to use it though-read some more, discovered I needed to go to Computer Management-Disc Management.

Very helpful!! For additional information on this limitation, please contact Microsoft Knowledge Base Article 184006. See below: BIOS Settings Typically, a message is displayed on the screen after the memory count of the boot process telling you how to enter Setup (system BIOS). Jun 18, 2007 #8 engg_g_s TS Rookie Topic Starter Sorry i didnt get the meaning of this statement .Does your mobo support an IDE detect timer or staggered spin-up or both?Pls

Getting it ready for use takes a little longer. Joshcore, if you are blindly defending your precious website PC Mech, then please, at least have a decent reason to do so. There is generally no need to change the default jumper setting in order to use the drive. To others out there who are stumped by techy terminology, I suggest browsing a little bit more sites & things will fall into place.

© Copyright 2017 wphomeguide.com. All rights reserved.