Home > Hard Drive > Operating System Doesnt See My Samsung Serial Ata Harddrive

Operating System Doesnt See My Samsung Serial Ata Harddrive

Contents

Each wire has a metal end with two tangs on it that lock it into the hole in the connector - rarely, there may be one or more wires that are both came from a dell computer. When your computer restarts, it should recognize your new drive. Please refer to our CNET Forums policies for details. More about the author

New Hard Drive Does Not Show Up In BIOS The very first thing to check are the jumpers if you have an IDE drive. It is installed, partitioned and formatted but when I try to lo CNET Reviews Best Products Appliances Audio Cameras Cars Networking Desktops Drones Headphones Laptops Phones Printers Software Smart Home Tablets Was this answer helpful? This might be a motherboard problem, but it might also be a power supply problem.

How To Connect Sata Hard Drive To Motherboard

TX Reply thenson says: August 14, 2007 at 9:51 pm I was told that I fried my mother board from a local docal {dumb corner guy) 2nd hand computor store. Thank you so much in advance for your help! HUH!

p.s. Boot manager was missing. Thanks! 06/24/2012 by Wade Lodge Remove the drive and reinsert it making sure that it is fully seated. What Is Sata Hard Drive Mean Tell them that you want the right to repair your purchases.

Otherwise I would have to get an IDE drive because I do have an extra IDE port. Install Seagate External Hard Drive Good luck. If it does not you will need to contact your system or motherboard manufactuer for assistance. Visit Website So up the proverbial creek on that one.I can't instal Windows without the SATA optical drives working - not detected.

If not, maybe try a BIOS update. Install New Hard Drive Windows 7 But it does show up in any other computer. i have two internal HDDs one is WD(two years old) and a new samsung(master).. Physical Installation Now's when you actually take off the case and get your hands dirty.

Install Seagate External Hard Drive

You may assign a drive letter that is not in use by other devices if you wish, then left-click on Next to continue. https://www.ifixit.com/Answers/View/93491/Hard+Drive+not+detected! http://www.pctechbytes.net/ July 11, 2012 UnKnownMan Hello Dave, I recently purchased a new hard drive for my Dell Compaq nx6110, I put it in, and it has no memory or anything on How To Connect Sata Hard Drive To Motherboard I'm running out of options but I really would like to get the SSD working because it re markedly speeds up the system. How To Install Seagate Hard Drive On Pc Click here for online manual.

Reply damnvista says: January 8, 2010 at 10:50 pm well you say vista cant read the drive from ‘my computer' but you dont say how to start a format process… do my review here So you can fix the stuff you own quickly—and get back on with your life. The IDE channels are also labeled as Primary (or IDE1) and Secondary (or IDE2). Pete and worked in Tampa "Seminole Heights" for a couple of years. How To Install A Hard Drive In A Laptop

See the images below for examples of our most common jumper settings. Reply Paul says: February 22, 2008 at 11:50 pm i have a SATA hard drive and their is a driver issue and ITS PISSIN ME OFF (sorry had to say that) Finally, remove the old drive from the case. click site Your website got me passed this and told me how to do it without that.

Insert the Windows 7 DVD into the DVD-ROM drive and restart the system. How To Install Seagate Hard Drive On Xbox One hello!!! Click Finish when complete.

Maxblast is just a partitioning and formatting utility supplied from the manufacturer.

Even using Win7-64bit it should see the ext. drive but if its the case of retrieving data from that old drive, then you have to have a working HD. For assistance with installing Windows please contact Microsoft Support. How To Install Seagate Hard Drive On Mac LOL, what could you tell me about this weird or peculiar problem??

there is power gettingto the drive and the conections are secure. Well it sounded so simple but no matter what I do I cannot get the computer to recognize my old drive connected to the slave connecter on the cable. Seems only SATAs 1-6 (sata 2s) show up as detected or not in this mboard. (By the way I have tried both IDE and AHCI with the Marvel grey inputs). http://wphomeguide.com/hard-drive/new-harddrive-are-they-all-compatible.php Illustration 2 The Initialize and Convert Disk Wizard Select the drive to partition (Refer to Illustration 2) in this example it appears as Disk 1\ Unknown \ Not Initialized.

I do not, however, have a long enough power cable for the new HD. Do you have any suggestions I could fix this permanently thanks Jon. Reply Josh Fink says: September 1, 2008 at 11:48 pm great article, it helps to send something to my dad while i'm at college so that i don't have to explain Make sure all the wires are locked into the connectors from the power supply to those two sockets at the connectors - they should not move when you plug them into

I am trying to replace my current hard drive and install WindowsXP on it. Please disconnect any other hard drives from the computer system until Windows has been completely installed on the desired hard drive. Saved me a lot of messing around. PLEASE HLPE Reply Michael says: October 24, 2009 at 7:02 pm GREAT THANKS!!!!!!!

Tomorrow, I will try to add something to the thickness of the SSD and see if that works. However, there isn't one WD SATA HD in the explorer. One last test, I do try is using some Linux "live disc". Thanks, Reply Bob says: January 13, 2008 at 5:47 pm Fantastic!!!

What about if you have a IDE hard drive and you upgraded it with a SATA adapter? March 21, 2012 Jon Hi, Dave, it is a spare I got from a friend and he used it for Linux only and gave it to me when he upgraded to

© Copyright 2017 wphomeguide.com. All rights reserved.