Home > Hard Drive > Need QUICK Help Connecting My Hard Drives And Cd Rom; Slave/master

Need QUICK Help Connecting My Hard Drives And Cd Rom; Slave/master

Contents

You'll need to fdisk this. made a huge difference.Long story short, spend 50$ get a seagate or Western digital 320 to 500gig drive. Yes. No, create an account now. this content

Install Windows with everything connected. Limit Capacity Option - This option may be required if the system the drive is being installing into does not support the full capacity of the drive. Does the master/slave selection effect operation of SATA drives? The basal step is: Boot into Windows.

Ide Hard Drive Jumper Settings

Thanks all 3 answers Last reply Aug 21, 2010 More about hard drive cable drive C00lITAug 18, 2010, 4:17 AM You can put in 2 devices on 1 IDE Cable you This cable is keyed therefore should only connect to the computer one-way. Binary Heap where a comparison delegate is used The most outrageous (or ridiculous) conjectures in mathematics Do you know that language? Read more.

Then I connect the cable up, bearing in mind that the hard drive as the master should be connected to the centre of the cable, with the slave CD-ROM drive being Once you're in the BIOS you'll want to go into standard CMOS where you should see something like this: Run the system setup program. And it doesn't matter which is at the end if there are two drives on the cable. How To Connect Ide Hard Drive To Motherboard Software setup IDE/EIDE CD-ROM drives only require the one or two CD-ROM drives for the drives to work.

Now, look at one cable. How To Connect Ide Hard Drive To Sata Motherboard Keep the drive in the protective anti-static container until ready to install. CD Drive and Hard Drive on same ide cable Connecting DVD SATA powered to 2nd SATA connector on SATA Hard Drive cable. http://www.makeuseof.com/tag/install-ide-hard-drive/ Notes: The standard 40-wire ATA ribbon cable and the 80-wire cable give different drive behavior when using Cable Select.

a7n8x Deluxe - Optical Drives Master/Slave Problem Master/Slave Hard drives master/slave for drives??? How To Install Ide Hard Drive Articles & News Forum Graphics & Displays CPU Components Motherboards Games Storage Overclocking Tutorials All categories Chart For IT Pros Get IT Center Brands Tutorials Other sites Tom's Guide Tom's IT i think my problems before were due to the fact one ide disk had the boot record on it, but windows was installed on a different disk, the sata disk. But be sure to use the diagram on each device for its setting - there is no universal system.

How To Connect Ide Hard Drive To Sata Motherboard

Of course, there are SATA channels, but I can't use them, because none of the devices is SATA. –Tom Feb 15 '10 at 19:57 @Tom - in that case http://www.mikeshardware.com/howtos/howto_connect_ide_hd.html Inside your computer, you generally have two (2) IDE hard drive controller connections. Ide Hard Drive Jumper Settings When connecting IDE devices in your computer, there are a few rules you need to know about. How Many Hard Drives Can Be Connected To A Single Ide Cable There is a connector at each end of the cable and another one about two-thirds of the distance from the motherboard connector.

ide harddrive and cdrom on same cable...It's slow so I sold them a recertified 500gig for 30$... http://wphomeguide.com/hard-drive/original-hard-drive-as-slave-no-access.php Reply Adam August 24, 2016 at 3:50 pm Did you have to reformat the HDD to run as a slave on the newer box? The BLACK one on the other end goes to whichever device you have set as Master (via jumper). solved 0x80070017 error when installing OS despite swapping disks, cables, DVD ROMs and hard drives solved Upgradeing PC useing same hard drive solved Need help installing Windows 10 with same hard Why Is It Necessary To Partition The Hard Disk While Installing Operating System?

BUY NOW FREE TRIAL BACKUP & RESTORE For Business » Todo Backup WorkstationBuyTry Todo Backup ServerBuyTry Todo Backup Advanced ServerBuyTry For Home & Home Office » Todo Backup FreeDownload Todo Backup Make sure you select quick format or else it'll be a while before you can use the disk. You might as well take the time to clean the house because that takes forever.My experiment was to sell a friend a really cheep computer... 200$ for an AthlonII 250... have a peek at these guys I assume that these cables are fairly readily available from places like Dick Smith. 08-08-2005,03:42 PM #2 drcspy View Profile View Forum Posts Private Message Long Time Member Join Date

Only older computers (the AT type) have a problem here, and again, you should read the manual that came with the motherboard or contact the maker of the system. Master Slave Hard Drive Jumper Settings Set each optical unit to Slave. Make sure both of the drives aren't set for the same setting (master or slave).

Required fields are marked *Comment Name * Email * James Bruce 628 articles James lives in the middle of nowhere with his wife, son, and chickens.

Cable Select is defined in the ATA-2 and ATA-3 specifications. For the CD-ROM, the diagram indicates that 2 is Slave setting. Basically, you’re looking for something that mentions CS or Cable Select, as well as Master, and Slave. Seagate Ide Hard Drive Jumper Settings One pin was removed that was never used so people installing hard drives wouldn't connect them backwards.

An unused drive power cable for your new drive. I removed a drive, now I cant boot anymore to my second drive. Save and exit the system setup program. http://wphomeguide.com/hard-drive/master-to-slave-virus-transfer.php solved Ide hard disk and ide dvd drive don't work at same time Can I put a DVD drive and a HDD drive on the same IDE cable? 3rd hard Drive

The Master drive goes on the black connector at the end of the cable, the slave drive connects to the gray connector in the middle and the host adapter connects to How to twist focus ring without shaking camera? This side of the cable almost always points to where the power connects to the CD-ROM drive. Entertainment Sling TV vs.

Perhaps a solution is around the corner as there is a draft for a FireWire ATA interface. Troubleshooting Additional computer CD-ROM help and support. ide channel 2 master: pioneer dvd-rw ---> my pioneer dvd/rw is this ok? Reply Www.diolt.com February 28, 2011 at 10:27 am Hello thanks for the nice information you shared Reply FreeReferrals February 27, 2011 at 9:40 pm Thanks this was very helpful and I

is that ok? right now i have the following connected like this, i'm reading from my bios: ide channel 3 master: wd250js ---> wester digital sata 250gb disk, partitioned on one of 50gb which A lot of people like to use what is called Cable Select. The time now is 08:53 PM.

Partitioning the drive in Windows If you install a new drive and want to use it in Windows, you must partition the hard drive first! The 80-wire cables are not called 80-pins! On each channel, there is a master and a slave device. Once verified, save the settings and reboot the computer.

The power cable you will plug in has four female plugs in it, and will only go in one way due to the shape of it, so that shouldn’t be too Fruit Bat /\0/\ 15:56 20 Dec 09 I should set this as primary and the cd rom to slave?yesor cd rom will slow down the hard drive to a crawl. CMOS setup Once the disc drive has been connected to the computer, place the case back onto the computer and connect the keyboard, monitor, and power to the computer (we recommend They had to be called something.

The difficult part is the jumper settings, which will vary according to your device.

© Copyright 2017 wphomeguide.com. All rights reserved.