Home > Hard Drive > Need Help Setting Up SATA Hard Drive.

Need Help Setting Up SATA Hard Drive.

Contents

Doing so voids the warranty. By the four sentence, you are assuming that everyone reading this will understand what ‘jumpers' are. both came from a dell computer. wikiHow Contributor Talking to a tech professional (like a specialist at a store selling computers and related items) would be best. check over here

When it runs a self test the drive is detected but only when I press f1 to enter setup and then it will not enter setup. With XP and 2000, though, use Windows' Disk Management utility. If so, hunt for a free Molex-style lead. Data transfer speeds range from 150MB/sec (SATA) and up to 300 MB/sec (SATA II). http://www.pcworld.com/article/131231/how-to-install-a-new-hard-drive-in-your-desktop-pc.html

How To Connect Sata Hard Drive To Motherboard

If so, screw a set onto the new drive (look inside the case for spares), then slide the drive into its bay. In mainstream cases, drive connectors will typically point to the rear. Host adapter configuration is shown below.

The guide you need is directions to your nearest PC repair shop and let that $6 per hour trainee do it for you. Then, power down your PC, unplug all cables, and open the case. This could be the DEL, ESC, or F1 key. Sata Interface Cable Your page sent me through the steps I needed and "I'm OK now" Thanks guys, I'll be back!

In addition, I linked to two articles right below the video that describe hard drive installation more in depth for anyone who needs it. Install New Hard Drive Windows 7 CyberTech 101.024 görüntüleme 2:33 How to Replace a Desktop Hard Drive - Süre: 5:54. Lets see what will happens. A+ on the info!

Connector on Motherboard If your computer is not the latest model and initially came with an IDE hard drive, the motherboard might not provide a SATA connector. How To Install A Second Hard Drive Someone that explains so even I can do it. Took me hours of wading through other websites of gobbledygook to get nowhere. Not all laptop hard drives are secured by screws. 5 Pull the ribbon to release the hard drive.

Install New Hard Drive Windows 7

How do i remove this data? http://www.wikihow.com/Install-a-Hard-Drive They are secured with screws or, in some more expensive computer cases, tool-less snap-in brackets. How To Connect Sata Hard Drive To Motherboard Show More Installing an internal hard drive is one of the more How To Install A Hard Drive In A Laptop Type fdisk/status to verify that your hard drive is present and recognized by the system. 4.

The image below shows what SATA (red, left) and IDE (grey, right) cables look like. check my blog ok the c drive does not have that much memary i took the c drive out and tryed to put a new one in but the hook ups on the drive Marco Chiappetta Screws are the best way to secure your hard drive into your case’s drive cage. Prepare the hard drive for use Once you’ve mounted and connected the drive, power up your system and enter the BIOS/UEFI. How To Connect Hard Drive To Motherboard

If you need to transfer your data (sometimes called data migration or clone) you can use the Seagate utility DiscWizard. In enthusiast-class cases, it’s becoming more common to see the drive’s connectors facing the right side, making it easier to route and hide cables behind the motherboard tray. Does Scandisk find the drive defect-free? this content I am new to SATA drives, and used to EIDE so didn't know I had to initialize it.

Then check whether a CD comes with the drive, providing drive-specific information and general upgrade assistance. How To Format A New Hard Drive Reply Janna says: August 27, 2007 at 3:26 pm I have a problem! Hope you can help, so far this has been a longwinded exploraton of my computer.

Don't know if it's important, but i'm running XP.

The Hard Drive only came with a CD, no floppy disk. New box HD is SATA. Make sure the panel is securely closed. How To Install A Hard Drive In A Pc I just installed a new SATA drive but couldn't figure out how to get Windows XP to recognize it and assign it a dive letter.

Make sure you plug into a SATA 6Gbps/SATA 3.0 port if you're installing a solid state drive. In the BIOS, go to the standard System Settings menu or the Integrated Peripherals > SATA menu to see all of the drives installed in the system. Should i just go ahead with formatting it as a removable drive? http://wphomeguide.com/hard-drive/my-western-digital-200gb-sata-hard-drive-keeps-disappearing.php I had no idea that "disk management" section existed 😀 Once i found it i initialized the HD and am currently formatting it.

the c drive that im using now as like no memary some one told me to stick them in my d/cd or my e/dvd/cd drive to keep them out of my thanks Reply Andy says: August 23, 2007 at 7:22 am walter, you need to copy the drivers from the CD to a floppy and then use the floppy disk during installation Having said that, this is a great article, A+. This panel is located on the bottom of the laptop.

Show More Installing an internal hard drive is one of the more PlayStation Vue: How Do They Compare? one of the 20 GB is Primary and the other two are slaves. The drive should slide directly in, and the holes on the side of the drive should line up to the screw guides on the housing.

If your computer does not automatically detect your new drive, follow the steps below. 1. electronhacks 147.169 görüntüleme 5:54 Build Your Own PC: Step 5 - How to install a SATA Hard Drive - Süre: 1:32. Thank you so much for this information… I was going in to my computer and to no avail didnt see the second hard drive. Finished!

Mounting your hard drive Physically mounting the hard drive in a PC is probably the most difficult part of the installation process.

© Copyright 2017 wphomeguide.com. All rights reserved.