But just to be sure, check the documentation to verify how to set that jumper for slow-SATA use in case that's what your machine needs. I also am having this problem. Is it a faulty harddrive or something not set correctly. This continues for almost an hour. his comment is here
If in doubt as to which 'Other Device' is your drive, then select each unknown device in turn and select 'Update driver'. Use the 'Browse My Computer for driver software' Check Did you install Windows on drive 2 with drive 1 removed? Tom's Hardware Around the World Tom's Hardware Around the World Denmark Norway Finland Russia France Turkey Germany UK Italy USA Subscribe to Tom's Hardware Search the site Ok About Tom's Hardware He is looking for solutions. –Farhan Jul 13 '14 at 18:09 add a comment| up vote -2 down vote I would suggest it is that the HD's on board electronics have http://www.techspot.com/community/topics/my-2-sata-hard-disks-are-showing-up-as-unkown-devices-and-wont-boot.73669/
The first thing is whether your device is listed within disk drives of not. Up until yesterday I used to have only Drive nº1 connected to the computer, but today I tried to connect both of them and now the BIOS only detects Drive nº2 The problem appears to be the disk and or volume drivers which Windows refuses to install automatically for additional SSD's and HDD's. While searching for drivers by any method provided (search Word for low level noise among restless crowd, as sign of confusion or complaint?
Boot manager was missing. Have you looked at the settings in the BIOS to make sure the the drive is set to Auto Detect settings? share|improve this answer edited Jun 25 '12 at 10:54 answered Jun 25 '12 at 10:46 Timothy G. 194 add a comment| up vote 1 down vote I read this Microsoft article Volume Information For This Disk Cannot Be Found After that I could notice that the system is very slow in booting up.
I see disk under Devices and Printers as USB to S-ATA now but everything is empty. Hard Drive Not Showing Up In Disk Management any ideas?!? Should I take the jumper off and try again? I would try putting the device in a different USB port and if that doeskin work try another machine.
Cloning a drive sector by sector would not be a problem if it were a virus, nor would check disk fail to complete. External Hard Drive Not Showing Up In My Computer Reply shantanu May 17, 2013 at 6:44 pm Hello, The first thing you should do is, to download and install the latest Chipset, storage controller & USB 3.0 driver ( USB Can you please help me to solve this problem that I could recover some data? March 21, 2012 Dave Is this your main boot drive or a spare storage drive?
Check the screenshot above to confirm that my Seagate Go Flex USB device is listed there. http://dtidatarecovery.com/troubleshooting-basic-hard-drive-problems-does-not-show-up-in-my-computer/ Glad you got it working. External Hard Drive Shows Up In Device Manager But Not My Computer I have a dell demension 8200 desktop which was seriously infected where I could not do anything with it. Hard Drive Shows Up In Bios But Not Disk Management March 7, 2012 DuROi Hi Dave, i have a old Vaio VGN-FS115M with a Hitachi 80Gb hard disk.
Reply shantanu May 4, 2013 at 4:47 pm You can follow the link in my comment just above your comment. this content When we checked the drives on the f12 menu the first 1 passed but the second aborted the diagnostic. Instead, run file recovery software to attempt to recover the data first. Now, restart your computer and update your chipset and USB drivers or simply run Windows update and select any hardware driver updates ( from the optional updates section ) and install Hard Drive Not Showing Up In Bios
Can you hear or feel the drive spinning up? Other than that its not visible anywhere . My desktop is acting just fine I've run CHKDSK and I'm not getting any errors or BSOD's. http://wphomeguide.com/hard-drive/new-external-hard-drive-not-showing.php The second HDD used IDE, and it went through as well.
Not really sure what the problem is, but based on the hard drive size, it sounds like an older drive that may have died. Convert To Dynamic Disk it is a hassle that i need to use my old computer just to use it. Sar September 26, 2013 10:49 am Reply # Hi, I am basic computer internet user.
I have tried pressing F8 to get into the options to recover the machine but this does not work. A tale of two sources: Is TLS *defense* against Man-in-the-Middle, or not? In rare cases this process might even be needed in VISTA, but I would not expect that.The other option for XP and earlier is to use a feature now common in External Hard Drive Not Showing Windows 10 These are sometimes referred to as Master and Slave.
but only one is working, other one gets detected in the BIOS but not in windows. There are couple of folders that are very important to me personally and some folders that would cost a fortune. there is nothing wrong with the laptop, no noises made by the HDD, it works perfectly and when i try to boot it up the HDD is not found anymore and check over here If you are good with command line tools, you can use Test disk for Windows to recover your data Reply Christopher May 12, 2013 at 11:37 am thank you for response
Research directions in persistent homology Why is generating 8 random bits uniform on (0, 255)? I have 3 internal harddrives. David Mohyla March 6, 2013 4:22 pm Reply # Hi, I would think that you are booting slower because the Operating System is looking at another device and confirming it is March 20, 2012 Dave If you installed Windows on drive 2 with drive 1 installed, it should have added something to the bootloader giving you the option to boot to either
I've kept my old PC intact and I've found that I can access both of these hard disks just fine if I plug them into my old PC so I know This realy helped. I have formatted, delete and re-created a single partition hoping it would work so i can use file recovery to recover my files but it wouldn't format either and it still Now i open Disk Management it take time and says loading disk configuration information, still 30 mins it says loading disk configuration information.
T Status BAD” mean when reported by the BIOS about my hard disk? I downloaded a self booting diagnostic tool from Seagate onto a floppy but it wont boot. I am posting this for other that might have the same problem. However, I can take my hard drive out and put it in a caddy, attach it to my other computer via USA and all the files are there and readable.
Reply shantanu May 11, 2013 at 6:43 pm Right Click the computer icon and click on Manage -> click on Storage -> click on Device management . Open your Seagate Free Agent drive to remove the casing. 3. November 30, 2012 Cristu Rares So dave, i have 2 hdd on my pc one WD 80GB connected via IDE cable and a new one WD 1TB connected via sata. In the disk manager you can see both the physical and the logical hard drives connected to the computer.
Look on the VAIO site for your model and see if they have any BIOS updates available, otherwise, you may need to figure out what motherboard and BIOS is currently installed The 1TB drive in non bootable. What is another step I could take to possibly use my hard drive? December 23, 2012 Dave Is this a custom build?
© Copyright 2017 wphomeguide.com. All rights reserved.